I nostri prodotti RFID
-
Linea Presse per Pinne
-
Pinna Die
-
Utensili manuali
-
Olio evaporativo per pressa a pinne e piegatura del tubo
-
Espansore tubolare per scambiatore di calore
-
Macchina automatica per l'inserimento di tubi a pinna
-
Piegatubi per scambiatore di calore
-
Forno per brasatura ad alta temperatura
-
Evaporatore del frigorifero che fa la macchina
-
Macchina del forno dello scambiatore di calore
-
Macchina per brasatura
-
Macchina per tubi di rame isolanti
-
Raccordo in rame che fa macchina
-
Macchina piegatrice per bobine
-
Macchina piegatrice di ritorno
-
Punzonatrice per tubi flangiatrice
-
Macchina per la pulizia della piegatrice di ritorno
-
Macchina della bobina del pancake
-
Macchina per il taglio del tubo
-
Perforatrice per fori per tubi
-
Macchina per collare piccolo tubo
-
Macchina integrata per tubi
-
Macchina per la chiusura di tubi
-
Macchina per l'inserimento di anelli
-
Raffreddatore d'aria Piastra Bordo Piegatrice
-
Macchina per la fusione di tubi di rame e tubi di alluminio
-
Piegatubi
-
Macchina per la formatura di estremità di tubi
-
Apparecchiatura per prove di perdita di elio
-
Macchina per la produzione di anelli di saldatura
-
Piegatrice per tubi a serpentina
-
Filatrice
-
Ricambistica
Piegatrice a serpentina per tubi
Piegatrice per tubi in alluminio completamente automatica per frigoriferoFunzione dell'attrezzatura: 1. La macchina è di una struttura su dieci, cioè piega dieci tubi contemporaneamente.
2. L'intera macchina adotta il servoazionamento, l'azionamento idraulico e l'azionamento pneumatico.
3. Il sistema di controllo elettrico è controllato da PLC + touch screen. PLC adotta il marchio Mitsubishi, il touch screen adotta il marchio Taiwan Weilun e gli apparecchi elettrici a bassa tensione adottano il marchio Schneider. Principio di funzionamento:
1. The pipe bender is mainly composed of discharging device, straightening device, primary feeding device, cutting device, secondary feeding device, bending device, table rotating device, rack and electric control device. The whole action is driven by oil cylinder and servo motor, and the electric appliance is controlled by PLC + touch screen. The pipe bender is developed by imitating the imported automatic pipe bender. The action steps and technological process are completely the same as those of the imported equipment, which is relatively reasonable.
2.Put the whole coil into the discharging rack, and lead the pipe end to the feeding clamp of primary feeding. Press the start button, the primary feeding device will send the pipe through the cutting device to the secondary feeding clamp. At this time, the primary feeding clamp returns to its original position, stops working, the secondary feeding clamp starts working, and the pipe is sent into the bending wheel to start bending. When bending to a certain length, cut off the pipe and continue bending until the final bending is completed, and take out the bent single piece manually. Press the start button again, the machine will repeat the above feeding elbow action, so as to cycle.
1. The pipe bender is mainly composed of discharging device, straightening device, primary feeding device, cutting device, secondary feeding device, bending device, table rotating device, rack and electric control device. The whole action is driven by oil cylinder and servo motor, and the electric appliance is controlled by PLC + touch screen. The pipe bender is developed by imitating the imported automatic pipe bender. The action steps and technological process are completely the same as those of the imported equipment, which is relatively reasonable.
2.Put the whole coil into the discharging rack, and lead the pipe end to the feeding clamp of primary feeding. Press the start button, the primary feeding device will send the pipe through the cutting device to the secondary feeding clamp. At this time, the primary feeding clamp returns to its original position, stops working, the secondary feeding clamp starts working, and the pipe is sent into the bending wheel to start bending. When bending to a certain length, cut off the pipe and continue bending until the final bending is completed, and take out the bent single piece manually. Press the start button again, the machine will repeat the above feeding elbow action, so as to cycle.
RETA MACCHINA CO., LTD
Aggiungere: No.2 Xinghengyizhi Road, Cicheng Industry Park, Jiangbei District, 315000, Ningbo City, Zhejiang Province, China
Tel: +86-574-81106661
E-mail: info@retamachine.com
Ragnatela :www.retamachine.com
Ricerca correlata
- Tube Serpentine Bending Machine
Precedente Fustellatore a pinna